A new sofa cushion cover

The sofa on the screened porch finally has a proper foam cushion and that cushion now has a cover.  Using a combination of a sale and a great coupon, I was able to get the foam for about half price--a huge help.  I found some decorator fabric at Hancock's that was a very close match to the pillows I'd already made, so I was ready to go.

With the fabric doubled and wrong sides out, I drew around the foam for the top and bottom pieces.

The side piece was cut and seamed so that it is like a ring.  I needed continuous bias binding and cording for top and bottom edges.  The Quilter's Strip Ticket provided the correct large square size.  Above, the square is now resewn and ready to be cut into a strip.

Cording goes into the bias binding and is then pinned to the edges of both the top and bottom pieces.

Using a zipper foot on the machine, piping is sewn to the edges of both the top and bottom pieces. All corners are rounded making application of the continuous piping easier.

Next, the side piece is pinned to the top piece over the piping.

Here's the top piece with the side piece attached to it all the way around.

Then the bottom piece and the side are sewn together, leaving the back open to insert the foam.

The foam is inserted into the cover and pinned closed.

Back seam is hand stitched closed.  All finished.

Dan was lucky enough to get to meet little Demos last week and took an iPhone picture of him and his lovely mommy with his new quilt.

Chair Cushion tutorial

I started making cushion covers many years ago when my mother asked me to make one for a rattan chair in their Florida room. She had found a woman who would make all the square cushion covers, but she said she didn't know how to make the cover for the round cushion. I took the old cover apart, including the piping to see just how it had been constructed and then used the old pieces for a pattern. This is what is now called "reverse engineering." The new cover fit like a glove and my mom was very happy.



I really liked the foam cushion on the armchair and decided to get one for the rocker. The top and bottom of the cover were cut exactly an inch larger than the measure of the foam square. The side piece was cut 3/4 of an inch wider than the side measure. I had to seam the side piece because it was about 80 inches around, so I reinforced the seams by topstitching.




Using my trusty bias ticket, I made enough bias to go around both the top and bottom edges.



The bias is an inch and a half wide to account for the cording.



The cording goes inside the bias to create the piping. (Pin the cording to the bias when you start so that it doesn't slip out.)



Starting in the middle of a side, pin the bias with cording inside, to the raw edges of the top. Curve the bias to fit in each of the four corners.



When you reach the point where you started, cut the cording so that it meets the beginning end with no overlap. Trim the bias at a 45 degree angle and place it inside the leading edge.



Pin in place.



Use a cording foot or a zipper foot for all of the sewing involving the piping. I'm actually using what's called an overcast foot on my old Bernina. Sew around the entire top about 1/4 inch from the edge. This will insure that the raw edges of the piping don't slip when you are seaming the top and the edge piece.



Pin the edge piece in place striving to make sure that seams do not end up in the corners. When the two ends of the edge piece meet, add one quarter inch to each side and seam with right sides together. Finish pinning edge in place.



The edge piece, now in a ring, pinned in place looks like this. Get as close to the cording as you can when you sew this seam.



Here's the top and the edge turned right side out on the cushion for display. Apply piping to the bottom exactly as you did to the top and sew in place. Pin bottom to edge piece on three sides only.



I sew a line of stitching one quarter inch from the edge of the fourth side. It makes pressing it under much easier. Sew bottom to edge on the three sides and turn cover right side out. Press down the fourth side.



Put cover on foam cushion. (This is a little bit like putting a sock on an giant who can't help you by pushing.) Whip stitch the fourth edge closed and put that side of the cushion anywhere but in the front.



Here's the new cushion all ready for our dinner party tomorrow.